Use

■ Anchoring of rebar or threaded rods in concrete, masonry, voided stone and rock, hard natural stone and solid or hollow bricks and blocks.
■ Grouting horizontally and vertically, where extremely rapid setting, fast turn-around times are needed.
■ Best choice for inclement conditions, including cold temperatures and wet substrates.
■ Grouting in external environments where applications are subject to dynamic loads and vibrations.
■ Anchoring structural steel to concrete, safety barriers, balcony stanchions, canopies, signs, hand rails, racking, machinery, rolling cranes, masonry supports, stadium seats, reinforcing and starter bars.

Characteristics and Advantages

■ Sets up in dry, wet and flooded holes.
■ Cures down to -26°C (-15°F) when material is pre-conditioned to at least 0°C (32°F).
■ Styrene-free.
■ Available in single piston cartridges
■ Approved for threaded bars in concrete.
■ Allows fixings close to free edges.
■ Reduced drilling diameters i.e. 2 mm anchor clearance results in economic installation.
■ Flexible embedment depths.
■ Resistant to a wide range of chemicals, including aqueous solutions of acetic acid, aluminum chloride and aluminium nitrate at 10% concentration, jet fuel, diesel fuel, domestic kerosene and many other substances at 75°C (167°F) while retaining at least 80% of physical values.(See Chemical Resistance Guide).

Approvals/Certifications
■ ETAG 001: Part 5, Option 7 approval for M8-M30 galvanised and stainless steel threaded bars (see specifics below*).
*4.6, 5.8, 8.8 & 10.9 galvanised steel & A4-70 and A4-80 stainless steel & 1.4529 HCR
threaded bars in C20/25 to C50/60 non-cracked concrete.

Colour

Grey

Packaging

300 mL (10.1 US fl. oz) single piston cartridges/12 per case
850 mL (28.7 US fl. oz) single piston cartridges/8 per case

Use

■ Anchoring of rebar or threaded rods in concrete, masonry, voided stone and rock, hard natural stone and solid or hollow bricks and blocks.
■ Grouting horizontally and vertically, where extremely rapid setting, fast turn-around times are needed.
■ Suitable for cooler temperatures and inclement conditions, including -5°C (-23°F) temperatures and wet substrates.
■ Grouting in external environments where applications are subject to dynamic loads and vibrations.
■ Anchoring structural steel to concrete, safety barriers, balcony stanchions, canopies, signs, hand rails, racking, machinery, masonry supports, stadium seats, reinforcing and starter bars.

Characteristics and Advantages

■ Sets up in dry or damp holes.
■ Cures down to -5°C (23°F) when material pre-conditioned to 23°C (73°F).
■ Styrene-free and odourless.
■ Available in single piston cartridges.
■ Approved for threaded rods and reinforcing bars in concrete.
■ Approved for threaded bars and sockets in masonry.
■ Reduced edge and spacing values allowing critical applications.
■ Reduced drilling diameters of 2 mm clearance resulting in economic installation.
■ Flexible embedment depths from 8d -12d.
■ Resistant to full immersion in water, salt water, hot water <75°C (167°F), citric acid, motor oil, methanol and kerosene (max. 25°C [77°F]) (See Chemical Resistance Guide).
■ Resistant to partial immersion in petroleum, gasoil, low concentration. sodium hypochlorite and other chemicals (consult Sika Canada for guidance).
■ Resistant to contact with concentrated sodium hypochlorite, acetone and toluene.

Approvals/Certifications
■ Fire tested with threaded bars to M24 F120 by iBMB, Institut Baustoffe Massivbau und Brandschutz.
■ Fire tested with post-installed rebar connections of 8 – 20 mm by CTSB, Centre Scientifique et Technique de Batimat, France
■ ANSI/NSF Standard 61 approved for contact with potable water.
■ Approved for masonry by DIBt., Deutsches Insitut für Bautecknik.
■ ETAG 001:Part 5, Option 7 approval for M8-M24 galvanised and stainless steel threaded rods (see specifics below*).
■ ETA approval to TR023 for post installed reinforcing bar connections.
■ ICC ES approved.
-AC308 ESR for uncracked concrete.
■ IAPMO approved.
*5.8 -8.8 & 10.9 galvanised steel, A4-70 and A4-80 stainless steel and 1.4529 HCR in C20/25
to C50/60 non-cracked concrete.

Colour

Packaging

300 mL (10.1 US fl. oz) single piston cartridges/12 per case
850 mL (28.7 US fl. oz) single piston cartridges/8 per case

Use

■ Anchoring of rebar or threaded rods in solid concrete, masonry, brick, block and stone.
■ Grouting horizontally and vertically, where slow-setting allows extended working time.
■ Suitable for deeper and scattered holes or applications where a fast-turnaround is not needed.
■ Grouting in external environments and where applications are subject to dynamic loads and vibrations.
■ Anchoring structural steel to concrete, safety barriers, balcony stanchions, canopies, signs, hand rails, racking, machinery, masonry supports, stadium seats, reinforcing and starter bars.

Characteristics and Advantages

■ Supplied as 1: 1 ratio in side by side cartridges.
■ Styrene- and VOC- free
■ Versatile material allows application as adhesive and anchoring gel.
■ Sets up in dry, wet or flooded conditions.
■ Cures down to 0°C (32°F) when material is conditioned to 5°C (41°F).
■ Cures without exhibiting expansion pressures.
■ Extended open and gel times accommodate anchoring in deep and scattered holes.
■ Permits anchors close to free edges.
■ Suitable for chemical anchors, threaded bars and reinforcing steel.
■ Performs in both cracked and non-cracked concrete
■ Resistant to a wide range of chemicals, including aqueous solutions of aluminum chloride at saturation, aluminium nitrate at 10% concentration, jet fuel, diesel fuel, domestic kerosene and many other substances at 75°C (167°F) while retaining at least 80% of physical values.(See Chemical Resistance Guide).
■ Supports high loads

Approvals/Certifications
■ ETAG 001:Part 1 approval pending.
■ ICC ES approved.
-AC308 ESR approved for cracked and uncracked concrete
■ IAPMO approved.

Colour

Bronze

Packaging

250 mL (8.4 US fl. oz) UVL cartridge/12 per case
600 mL (20.2 US fl. oz) side by side cartridges/12 per case
1500 mL (50.7 US fl. oz)side by side cartridges/5 per case

Use

■ Use to bond to concrete, steel, wood and tiles.
■ An excellent non-shrinking permanent crack or static-joint filler for concrete, wood and steel.
■ A ‘pick-proof’ sealant for custodial suites and holding cells.
■ Use to resurface horizontal and vertical concrete prior to applying Sikafloor^® or Sikagard^® resin systems.

Characteristics and Advantages

■ High- solids content with low VOC content.
■ Colour-coded to ensure complete and correct mixing.
■ Easy to mix (2:1 by volume ratio) and apply.
■ Thixotropic, non-sag characteristic allows horizontal and vertical application.
■ Self-priming, excellent adhesion to concrete.
■ Cures to provide hard and impact resistant material.
■ May be mixed with silica sand to produce patch repair material (consult Sika Canada Inc).
■ Very low water absorption and highly durable.
■ Fully compatible with Sikafloor^® and Sikagard^® resin systems.
■ Canadian Food Inspection Agency (CFIA) acceptance.

Colour

Grey

Packaging

Unité de 3 L (0,8 gal US)

Use

• Sika Loadflex is recommended for use as a filler for interior, horizontal saw cut or preformed control joints in facilities such as warehouses and plants, where such joints are subject to load bearing conditions involving wear and impact.
• Sika Loadflex is also used for repairing interior concrete slabs that have experienced random cracking due to shrinkage.

Characteristics and Advantages

• Hard load bearing sealant designed to withstand industrial traffic.
• Provides for even load transfer across floor joints, thereby protecting joint edges from breakdown.
• Seals joints from collecting dirt, dust, and debris.
• Easily installed by pouring or gunning.
• Excess material can be shaved off smooth as early as 12 hours.
• Canadian Food Inspection Agency acceptance.

Colour

Packaging

Use

• Sika Loadflex Polyurea is recommended for use as filler for interior, horizontal saw cuts or preformed control and construction joints.
• Typically installed in facilities such as warehouses and industrial plants, where such joints are subject to load-bearing conditions involving wear and impact.
• Sika Loadflex Polyurea is also used for repairing interior concrete slabs that have experienced random cracking due to shrinkage.

Characteristics and Advantages

• Quick-set formula reduces down time.
• Excess material can be shaved off smooth as early as 15 minutes or as late as 24 hours after placement at 23°C (73°F).
• Cures at temperatures down to -25°C (-13°F).
• Hard, load-bearing filler designed to withstand industrial traffic.
• Provides even load transfer across floor joints, thereby protecting joint edges from breaking down under traffic.
• Two components, easy to use, 1:1 mix ratio.
• Improved consistency to allow easier dispensing and reduced blockage of equipment.
• Seals joints from collecting dirt, dust and debris.
• Low modulus of elasticity.
• Improved moisture sensitivity.
• Approved by the Canadian Food Inspection Agency.

Colour

RAL 7038 Agate Grey and RAL 3009 Oxide Red

Packaging