Primers
Technical advice / Where to buy?
Sikafloor®-156
Sikafloor®-156CA is a two-component, solvent-free, low-viscosity, high-strength, epoxy resin, used as an epoxy primer and binder for Sikafloor® Systems.
Use
- Primer and adhesion promoter for all Sikafloor epoxy and polyurethane floors.
- Binder for epoxy mortar screeds.
- Bonding Sika mortars to various substrates.
Characteristics and Advantages
- Low viscosity.
- Good penetration.
- High mechanical resistance.
- Short waiting times.
- Excellent bond strength.
- User friendly.
- Neutral odour.
- Canadian Food Inspection Agency acceptance/USDA acceptance.
Colour
Clear amberPackaging
10 L (2.6 US gal.) unit30 L (7.9 US gal.) unit
Product Data Sheet
Sikafloor 156 CASafety Data Sheet
Sikafloor 156 CASikafloor®-1610
Sikafloor® 1610 is a two component, high solids yet low modulus and low viscosity, epoxy primer. This resin is highly penetrative, seals substrates, contains a red trace dye to allow coverage to be ensured and is of low-VOC content. Sikafloor® 1610 NA has been especially formulated to operate as a moisture tolerant adhesion promoter beneath Sikafloor® , Sikaguard® and Sikalastic® epoxy and urethane coatings, broadcast or trowelled systems.
Use
Designed for concrete substrates where Sikafloor® resin systems are due to be installed and a measured moisture content of < 6% (p.b.w. – part by weight), as determined with Tramex® CM/E type meter, exists.
Characteristics and Advantages
- Ease of application.
- Moisture tolerant.
- Excellent penetration.
- High bond strength.
- Low tensile modulus.
- Higher tensile elongation.
- Potential for LEED® Canada credits.
- Meets the requirements of CFIA and USDA for use in food plants.
Colour
Transluscent Red (after mixing)
Packaging
Unit of 18 L (4.7 US gal.)
Product Data Sheet
Sikafloor 1610Safety Data Sheet
Sikafloor 1610Sikagard® CorPro-470
(Formerly Cor-Pro 470) Sikagard® Cor-Pro 470 is a high performance, two component, solvent based, polyamide epoxy primer designed to provide increased adhesion and corrosion resistance properties over properly prepared ferrous and galvanized metal substrates.
Use
- Provides additional protection for metal substrates subject to severe environments.
- Suitable for interior and exterior applications.
- High performance epoxy primer for metal substrates used in combination withcompatible Sikafloor® and Sikagard® epoxy and polyurethane coatings.
Characteristics and Advantages
- Excellent adhesion on prepared ferrous and galvanized metal substrates.
- Extended pot life allows application by brush, roller or spray.
- Easy to apply and repair if damaged.
- Supplied ready to use, no additional thinning is required for most applications.
Colour
Grey, low gloss
Packaging
3.78 L (1 US gal.)
Product Data Sheet
Sikagard Cor-Pro 470Safety Data Sheet
Sikagard Cor-Pro 470Sikafloor® Vertical Epoxy Primer
Sikafloor® Vertical Epoxy Primer is a 100% solids, two-component, moisture tolerant, epoxy adhesive used as a primer for Sikafloor® cove and detailing mortars.
Use
- Sikafloor Vertical Epoxy Primer is used as a tacky primer and adhesion promoter for the vertical application of Sikafloor mortars.
- Primer for concrete substrates and most steel surfaces that have been properly prepared.
Characteristics and Advantages
- Excellent ‘tacky’ grab properties provide true ‘hang’ characteristics for vertical mortars.
- Suitable for application on new or existing cured concrete substrates.
- Can be applied onto 7 to 10 day old concrete after adequate preparation and where substrate has tensile bond strength in excess of 1.5 MPa (218 psi).
- Achieves bond strength in excess of the tensile strength of concrete.
- Moisture tolerant; maximum moisture content of concrete substrate < 10%.
- Flexible bond line provides good performance under thermally induced stress.
- Easy to mix: 1:1 ratio.
- Low odour as a result of 100% solids content.
- CFIA acceptance for use in food plants in Canada.
Packaging
3.1 kg (3.0 L) / 6.8 lb (0.8 US gal.) kit
Product Data Sheet
Sikafloor Vertical Epoxy PrimerSafety Data Sheet
Sikafloor Vertical Epoxy PrimerSikafloor®-165 FS
Sikafloor® 165 FS is a two-component, high-solids, low VOC, neutral odour, epoxy resin specifically formulated to perform as a rapid curing, adhesion promoting primer and concrete surface sealer for fast turn around applications.
Use
- As an adhesion promoting primer/ sealer for absorbent substrates including concrete and cement screeds.
- Penetrates substrate to reduce outgassing, minimizing the formulation of bubbles in subsequent body coats when applying Sikafloor® and Sikagard® systems.
Characteristics and Advantages
- Very rapid overcoating time increases productivity, 2 hours 30 min at 23 °C (73 °F)
- Low viscosity ensures excellent penetration and adhesion
- User friendly mix ratio, A:B = 3:2 parts by volume
- Low tensile modulus
- Higher tensile elongation
- Low VOC content, neutral odour
- LEED® Canada credits available.
- Meets the requirements of CFIA and USDA for use in food plants
Packaging
18.92 L (5 US gal) kits : Part A : 11.35 L (3 US gal) ; Part B : 7.57 L (2 US gal)