Sika AnchorFix®-3030
Epoxy high performance chemical anchoring adhesive
Sika AnchorFix®-3030 is an epoxy resin based, 2-part, thixotropic, high performance anchoring adhesive for anchoring threaded rods and reinforcing bars in both cracked and un-cracked concrete dry or damp concrete.
- Long open Time
- Sets up in dry, wet or flooded conditions
- High load capacity
- Seismic tested (design categories A to F and C1 & C2)
- Suitable for contact with drinking water
- Styrene-free
- Good adhesion to substrate
- Shrinkage-free hardening
- Low emissions
- Low wastage
Usage
Anchoring adhesive for fixing of non-expanding anchors in the following:Structural work
- Rebar / steel reinforcement anchoring in new and refurbishment works
- Threaded rods
- Bolts and special fastening / fixing systems
- Handrails, balustrades and supports
- Railings
- Window and door frames
- Concrete (cracked and un-cracked)
- Hollow and solid masonry
- Wood
- Natural and reconstituted stone
- Solid rock
Advantages
- Long open Time
- Sets up in dry, wet or flooded conditions
- High load capacity
- Seismic tested (design categories A to F and C1 & C2)
- Suitable for contact with drinking water
- Styrene-free
- Good adhesion to substrate
- Shrinkage-free hardening
- Low emissions
- Low wastage
Packaging
385 mL dual cartridge | 12 cartridges per box Pallet: 70 boxes with 840 cartridges |
585 mL dual cartridge | 12 cartridges per box Pallet: 44 boxes with 528 cartridges |
Colour
Part A |
Off white |
Part B |
Grey |
A+B mixed |
Light grey |
Product Details
ENVIRONMENTAL INFORMATION
- Conformity with LEED®v4 IEQ Credit: Low-Emitting Materials.
APPROVALS / CERTIFICATES
- ICC-ES Evaluation Report, ESR-4778: approved for cracked and uncracked concrete.
- Meets ASTM C881 (Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete Type I & IV, Class C, Grade 3).
- ANSI/NSF Standard 61 approved for contact with potable water by IAPMO-R&T.
- Ministère des Transports du Québec (MTQ) approved.
- Ministry of Transportation of Ontario (MTO) approved.
- Waiting to be approved by the British Columbia Ministry of Transportation (BC MoT).
Composition / Manufacturing
Epoxy resin
Shelf Life
24 months from date of production
Storage Conditions
The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +10 °C and +25 °C (+50 °F and +77 °F). Always refer to packaging.
Density
A+B mixed | 1,5 kg/L |
Volatile organic compound (VOC) content
2 g/L
Compressive Strength
95 MPa / 13 779 psi (7 days, +20 °C / +68 °F) | (ASTM D 695) |
Tensile Strength in Flexure
45 MPa / 6 527 psi (7 days, +20 °C / +68 °F) | (ASTM D 790) |
Tensile Strength
23 MPa / 3 335 psi (7 days, +20 °C / +68 °F) | (ASTM D 638) |
Service Temperature
Long term | -40 °C min. to +50 °C max. |
Short term (1–2 hours) | +70 °C (+128 °F) |
Application
Mixing Ratio
Part A : Part B = 3 : 1 by volume
Layer Thickness
~8 mm max
Sag Flow
Non-sag, including overhead
Product Temperature
+10 °C min. to +40 °C max. (+50 °F min. to +104 °F max.)
Ambient Air Temperature
+5 °C min. to +40 °C max. (+41 °F min. to +104 °F max.)
Dew Point
Beware of condensation.
Substrate temperature during application must be at least +3 °C above dew point.
Substrate Temperature
+5 °C min. to +40 °C max. (+41 °F min. to +104 °F max.)
Curing Time
Temperature | Open time - Tgel | Curing time - Tcur |
+35 °C to +40 °C | 6 minutes | 2 hours |
+30 °C to +35 °C (+86 °F to +95 °F) | 8 minutes | 4 hours |
+25 °C to +30 °C (+77 °F to +86 °F) | 12 minutes | 6 hours |
+20 °C to +25 °C (+68 °F to +77 °F) | 18 minutes | 8 hours |
+15 °C to +20 °C (+59 °F to +68 °F) | 25 minutes | 12 hours |
+10 °C to +15 °C (+50 °F to +59 °F) | 40 minutes | 18 hours |
+5 °C to +10 °C* (+41 °F to +50 °F) | 150 minutes | 24 hours |
+5 °C* (+41 °F) | 300 minutes | 24 hours |
* Minimum cartridge temperature: +10 °C (+50 °F)
SUBSTRATE QUALITY
Mortar and concrete must be at the required design strength.
Substrate tensile / compressive strengths (concrete, masonry, natural stone) must be confirmed by testing.
The anchor hole must always be clean, dry, free from oil and grease etc.
Loose particles must be removed from the holes.
Threaded rods and rebar's must be cleaned thoroughly and free from dirt, oil, grease, corrosion products or any other substances and particles which could affect adhesion.
MIXING
Preparing the cartridge: 385 & 585 ml
1.Unscrew the cap |
2. Remove the cap |
3. Screw on the static mixer |
4. Place the cartridge into the application gun ready for use |
When the work is interrupted the static mixer nozzle can remain on the cartridge after the gun pressure has been released. If the resin has hardened in the nozzle when work is resumed, a new nozzle must be attached.
CLEAN UP
Remove uncured material from all tools and application equipment with Sika® Epoxy Cleaner. Cured product can only be removed mechanically.