Sikaflex®-554
STP assembly bonding adhesive with acceleration option
Sikaflex®-554 is an elastic 1-component Silane Terminated Polymer (STP) adhesive system especially designed for bonding large components in industrial assembly. It bonds well to a wide range of substrates with minimal pre-treatment.
Sikaflex®-554 can be accelerated with Sika’s Booster and PowerCure systems.
- Good adhesion to a wide variety of substrates without primer
- Very good weathering resistance
- Passes DIN EN 45545-2 R1/R7 HL3
- ISEGA certificate for foodstuff area usage
- Curing can be accelerated with Sika Booster and Sika PowerCure
- Solvent-, isocyanate-, phthalate- and PVC-free
- Capable of withstanding dynamic stresses
PRODUCT BENEFITS
- Good adhesion to a wide variety of substrates without primer
- Very good weathering resistance
- Passes DIN EN 45545-2 R1/R7 HL3
- ISEGA certificate for foodstuff area usage
- Curing can be accelerated with Sika Booster and Sika PowerCure
- Solvent-, isocyanate-, phthalate- and PVC-free
- Capable of withstanding dynamic stresses
Usage
Sikaflex®-554 is suitable for joints that will be subjected to dynamic stresses. Suitable substrate materials: metals, aluminum, metal primers, paint coatings, sheet steel, ceramic materials and certain plastics. It bonds well to a wide range of substrates with minimal pre-treatment. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-554 on materials prone to stress cracking. Sikaflex®-554 is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed ensuring adhesion and material compatibility.Packaging
| Unipack | 600 mL |
| Cartridge | 300 mL |
| Pail | 23 L |
| Drum | 195 L |
Product Details
| Chemical base | Silane Terminated Polymer | |
| Colour (CQP001-1) | White, black | |
| Cure mechanism | Moisture-curing | |
| Density (uncured) | depending on color | 1.44 kg/l |
| Non-sag properties | Good | |
| Application temperature | ambient | 5 °C ─ 40 °C |
| Skin time (CQP019-1) | 25 minutes A | |
| Open time (CQP526-1) | 20 minutes A | |
| Curing speed (CQP049-1) | see diagram 1 | |
| Shrinkage (CQP014-1) | 2 % | |
| Shore A hardness (CQP023-1 / ISO 48-4) | 55 | |
| Tensile strength (CQP036-1 / ISO 527) | 3.5 MPa | |
| Elongation at break (CQP036-1 / ISO 527) | 500 % | |
| Tear propagation resistance (CQP045-1 / ISO 34) | 20 N/mm | |
| Tensile lap-shear strength (CQP046-1 / ISO 4587) | 2.5 MPa | |
| Service Temperature (CQP509-1 / CQP513-1) | -50 °C ─ 90 °C | |
| Shelf life | unipack / cartridge | 12 months B |
| CQP = Corporate Quality Procedure | A) +23 °C / 50 % r. h. | B) Stored below +25 °C |
CURE MECHANISM
Sikaflex®-554 cures by reaction with atmospheric moisture. At low temperatures the water content of the air is generally lower and the curing reaction proceeds somewhat slower (see diagram 1).
Diagram 1: Curing speed Sikaflex®-554
CHEMICAL RESISTANCE
Sikaflex®-554 is generally resistant to fresh water, seawater, diluted acids and diluted caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids, glycolic alcohol, concentrated mineral acids and caustic solutions or solvents.
Application
Surface Preparation
Surfaces must be clean, dry and free from grease, oil, dust and contaminants.
Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.
Application
Sikaflex®-554 can be processed between +5 °C and +40 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between +15 °C and +25 °C. Consider that viscosity will increase at low temperature. For easy application, condition the adhesive at ambient temperature prior to use. To ensure a uniform thickness of the bondline it is recommend to apply the adhesive in form of a triangular bead (see figure 1).
Figure 1: Recommended bead configuration
Sikaflex®-554 can be processed with manual, pneumatic or electric driven piston guns as well as pump equipment. The open time is significantly shorter in hot and humid climate. The parts must always be installed within the open time. Never join bonding parts if the adhesive has built a skin. For advice on selecting and setting up a suitable pump system, contact Sika Canada.
Tooling and finishing
Tooling and finishing must be carried out within the skin time of the product. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use.
Removal
Uncured Sikaflex®-554 may be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water.