SikaBond® Construction Adhesive
ONE-PART, ADVANCED POLYURETHANE, ELASTOMERIC ADHESIVE
SikaBond® Construction Adhesive is a one-component, durable and flexible exterior polyurethane adhesive/sealant. It has excellent adhesion on all cement-based materials, brick, ceramics, glass, metals, and wood.
- Excellent adhesion on all cement-based materials, brick, ceramics, glass, metals, and wood
- Fast cure rate
- Waterproof and water immersible after cure
- Good weathering resistance
- Non-corrosive
- Can be painted over with water, oil, and rubber-based paints. (Preliminary tests recommended)
- High durability and flexible
- Can be used to seal gaps
Usage
- Paver caps, masonry veneer and faux stone
- Submerged applications (ex. ponds)
- Mesh mounted tiles
- Floor moldings and door sills
- Light weight construction materials
- Wood or metal window and door frames
Advantages
- Excellent adhesion on all cement-based materials, brick, ceramics, glass, metals, and wood
- Fast cure rate
- Waterproof and water immersible after cure
- Good weathering resistance
- Non-corrosive
- Can be painted over with water, oil, and rubber-based paints. (Preliminary tests recommended)
- High durability and flexible
- Can be used to seal gaps
Packaging
300 mL cartridges: 12/case and 858 mL cartridges: 6/case (moisture-proof composite cartridges)
Colour
Grey
Product Details
Shelf Life
12 months in original, unopened container.
Storage Conditions
Store at temperatures between 4 and 35 °C (40 and 95 °F). Condition material at temperatures between 18 and 24 °C (65 and 75 °F) before using.
Volatile organic compound (VOC) content
33 g/L
Tensile Strength
1.55 MPa (225 psi) | (ASTM D412) |
Chemical Resistance
Good resistance to water, diluted acids, and diluted alkalines. Consult Sika Canada for specific data.
Service Temperature
-40 to 77 °C (-40 - 170 °F)
Resistance to Weathering
Excellent
Application
Ambient Air Temperature
4 to 38 °C (40 to 100 °F)
Substrate Temperature
4 to 38 °C (40 to 100 °F)
Curing Time
5 to 7 days
Skinning time
2 hours (depends on temperature and humidity) | (TT-S-00230C) |
Yield
300 mL cartridge yields 3.72 lin m (12 lin ft) of 12.7 mm (1/2 in) x 6.35 mm (1/4 in) joint.
858 mL cartridge yields 10.7 lin m (35 lin ft) of 12.7 mm (1/2 in) x 6.35 mm (1/4 in) joint.
SUBSTRATE PREPARATION
Clean all surfaces. Surface must be sound, clean, dry, frost-free, and free of oil and grease. Curing compound residues and any other foreign matter must be thoroughly removed.
Priming
Priming is not usually necessary for non-absorbent materials such as anodized aluminum, steel, glass, ceramics, stoneware and tiles.
CLEAN UP
Clean all tools and equipment with Sika® Urethane Thinner and Cleaner. Once hardened, product can only be removed mechanically.
FAQ
Avoid contact with silicone or high solvent-based sealers/paints.
Yes, but preliminary tests are recommended prior to using on porous decorative materials such as marble and other natural stones (prevent staining).
Ne pas utiliser sur des matériaux ou surfaces à base d’asphalte ou autres substances bitumineuses. Ne pas utiliser pour les joints de dilatation.
The SikaBond® Construction Adhesive will not bond to polyethylene, polypropylene, and polystyrene.
Do not use on PVC-based material.
Avoid exposure to high levels of chlorine. (Maximum level is 5 ppm.)
For cold weather application, condition material to +18 °C to +24 °C (65 °F to 75 °F) before using. Cut plastic tip of the nozzle to desired size and puncture airtight seal at base of tip. Force adhesive onto bonding surface. Use as spread, bead or for spot bonding. Heavier substrates may require additional support during the cure period.
Priming is not usually necessary for non-absorbent materials such as anodized aluminum, steel, glass, ceramics, stoneware, and tiles.
Allow a minimum of one (1) week cure at standard conditions when using SikaBond® Construction Adhesive in total water immersion situations, and since the system is moisture-cured, permit sufficient exposure to air.
Low temperature and humidity will slow the cure of the product. And finally, contact with alcohol and other solvent cleaners should be avoided during the cure.
Application temperatures (ambient air) are +4 to +38 °C (40 to 100 °F).
A 300 mL cartridge yields 3.72 lin m (12 lin ft) of 12.7 mm (1/2 in) x 6.35 mm (1/4 in) joint, while an 858 mL cartridge yields 10.7 lin m (35 lin ft) of 12.7 mm (1/2 in) x 6.35 mm (1/4 in) joint.