SikaTile®-330 PRO

• SikaTile®-330 PRO meets ISO 13007 international standard for the C2E classification
• SikaTile®-330 PRO meets ANSI A118.4E standard

Portland cement, selected aggregates, water retention additives, redispersible polymer

12 months from date of production when stored in original, sealed package

Store in undamaged, unopened, original sealed packaging in dry conditions at temperatures between 5 °C (41 °F) and 35 °C (95 °F). Protect from direct sunlight, heat and moisture.

ISO 13007 Classification

ANSI Method / 4 Week Shear Bond Strength

4.4 to 4.7 L (1.16 to 1.24 US gal) of clean potable water per 20 kg (44 lb) bag

> 2 ½ hours

≥ 30 minutes

SikaTile®-330 PRO meets A118.4E and ISO 13007 adhesion performance requirement for Extended Open Time 

Product curing time is affected by ambient and surface temperatures and humidity

* The consumption depends on the surface profile and roughness of the substrate and on the size of the tiles and the placing technique

JOB SITE CONDITIONS

Maintain environmental conditions and protect work during and after installation. Comply with trade and industry standards and manufacturer's printed recommendations.

When tiling in cool conditions in the work area, turn off all forced ventilation and radiant heating systems and protect the work. When necessary, use indirect auxiliary heaters to maintain an adequate temperature level in the working area (ambient and surface temperatures). Exhaust temporary heaters to the exterior potential harmfulness to the personal and/or to prevent damage to the work from carbon monoxide emissions. Maintain work area at a temperature no lower than 13 °C (55 °F) for at least 72 hours before and after installation.

SUBSTRATE QUALITY (for concrete or for cement mortar screed)

Surface treatments or any friable areas of the substrate must be mechanically eliminated. Aggressive mechanical preparation (such as but not limited to using a scarifier or a chipping hammer may invite micro bruising of the substrate) Contact Sika’s Technical Services for additional information. 

Resurfacing, patching, levelling or areas requiring a mortar screed should be prepared using appropriate SikaLevel® self-levelling, patching, or SikaScreed®-40 screed mortar. Expansion joints should comply with detail 301MJ Movement joint guidelines per TTMAC.

Warning: Refer to the Regulations Made Under the Canada Labour Code for additional information regarding requirements for handling surface containing or suspected of containing lead-based paints or any flooring, substrate or substances that may contain asbestos.

All supporting surfaces should be structurally sound, solid, stable. Surfaces shall be flat, plumb and true with a maximum permissible variation of 6 mm (1/4 in) in 3.05 m (10 ft) or no more than 3 mm (1/8 in) in 600 mm (24 in) from the required plane. However, any tile or stone with at least one edge greater than 380 mm (15 in) requires more stringent tolerances of the substrate with a maximum permissible variation of 3 mm (1/8 in) in 3.05 m (10 ft) or more than 1.5 mm (1/16 in) in 600 mm (24 in). Surfaces should be clean and free of dust, oil, grease, paint, tar, wax, curing agent, primer, sealer, form release agent and any deleterious substance or conditions that may prevent, reduce or inhibit adhesion or performance.

Before work commences, examine the areas to be covered and report any improper condition(s) in writing to the general contractor, architect or engineer (or otherwise, the owner). User shall not proceed with the work until surfaces and conditions comply with the requirements indicated in this document; applicable industry standards; federal, provincial and local regulations, as well as good trade practices. By starting work, the Applicator/User acknowledges that the conditions are acceptable.

Localized substrate repair variations of 5 mm (13/64 in) or less can be levelled with SikaTile®-330 PRO and allow to set at least 18 hours (or as soon as 3 hours when using SikaTile®-560 LFT Rapid).

Concrete (and cement mortar screed) 

Concrete must be cured for a minimum of 28 days (up to 14 days for cement mortar screed or only 5 hours when using SikaScreed®-40 screed mortar). On grade or below grade concrete slabs must be installed over an effective and continuous vapour barrier. On a clean and dust-free substrate, place a single drop of portable water (quarter size) on the substrate using a pipette. The concrete should turn dark. If the drop is absorbed within 60 seconds, the substrate can be considered porous (or absorptive) and acceptable for using SikaTile®-330 PRO. Otherwise, a bond test should be performed to confirm an adequate bond. If an adequate bond cannot be achieved, the concrete surface should be abraded, and additional bond tests should be conducted. If an adequate bond cannot be achieved or in doubt, contact Sika’s Technical Services. 

Note : As per TTMAC (Tile Terrazzo Marble Association of Canada) 09 30 00 guide. Concrete should have a steel trowel and fine broom finish for thin-set applications. Indeed, although not mandatory, a light surface profile can positively impact bond performances of cementitious tile setting adhesives.

In a clean container, add between 4.4 to 4.7 L (1.16 to 1.24 US gal) of clean potable water. Then add 1⁄2 bag of SikaTile®-330 PRO and mix at slow speed until a wet slurry is obtained. Add 1⁄4 bag and mix between 200-300 rpm until powder comes to a loose paste consistency. Add final 1⁄4 bag and mix thoroughly to a smooth and homogeneous consistency. SikaTile®-330 PRO consistency shall be such that when applied with the recommended notched trowel to the substrate, the ridges formed by the mortar do not flow or slump.

Note: No Slake Technology - No wait, just mix, trowel and install.

Choose a notched trowel with sufficient depth to achieve more than 80 % coverage of SikaTile®-330 PRO and transfer to substrate and back of tile for all interior applications.

For commercial floor, in applications in wet areas, for tiles that are going to be subjected to heavy traffic or exposed to high impact or for tiles with at least one edge greater than 380 mm (15 in), a minimum of 95 % coverage must be achieved. ''Flat back trowelling'' the tile which consists of applying a thin layer of SikaTile®-330 PRO to the back of each tile before setting it in place may be necessary to meet these requirements and it may also help improve adhesion to tiles with bond breakers such kiln release agents.

With pressure, apply a coat of SikaTile®-330 PRO by using the flat side of the trowel to key the mortar into the substrate. With the notched side of the trowel, apply additional mortar by combing it in a single direction parallel to the shortest dimension of the tile. Spread only as much mortar as can be tiled before the product skins over.

Place the tiles firmly into the freshly applied SikaTile®-330 PRO. Push the tiles back and forth in a direction perpendicular to trowel lines, to collapse the ridges which can help achieve better coverage with edges and corners fully supported. Ensure proper contact of the mortar to the back of the tile and to the substrate by periodically lifting a few tiles to check for acceptable coverage and verify that corner and edges are fully supported. Open time can vary with job site conditions. Remove excess SikaTile®-330 PRO from the joint areas so that at least 2/3 of the tile depth is available for grouting. Always allow SikaTile®-330 PRO to cure sufficiently before grouting and eventually opening to traffic.

MOVEMENT JOINTS

Expansion, control, construction, cold, saw-cut, isolation, contraction, and seismic joints in the structure should continue through the tilework, including such joints at vertical surfaces, as specified per TTMAC’s Specification Guide 09 30 00 Tile Installation Manual, Detail 301MJ. Do not cover movement joints with mortar. Use a suitable sealant instead (following manufacturer's written instructions). Always test a small inconspicuous area for staining or leaching before use to ensure compatibility on natural stones. 

GROUTING AND PROTECTION

Protect from impact and vibration for at least 48 hours. Allow at least 18 hours before grouting. Then protect grouted area at least 18 hours before allowing foot traffic and at least 24 hours before allowing light traffic depending on temperatures and humidity conditions. Protect from heavy traffic for at least seven (7) days. As necessary, use load distributing protection over the installation when moving heavy equipment across tiled assembly. 

Note: Extended protection and downtime requirements before grouting may be required depending on temperature and humidity conditions and on the porosity and size of the tile or stone being installed

PROTECTING NEW TILED FLOOR

Upon completion of tiled floor, it is the responsibility of the owner/agent or general contractor to protect the floor from damages (TTMAC’s Specification Guide 09 30 00 Tile Installation Manual).

Clean all tools and equipment after use with water. Once hardened, the product can only be removed mechanically.