King® MasonBond 400®
Polymer-modified mortar
King® MasonBond 400® is a premixed, factory-bagged mortar specially designed for the installation of cultured bricks, stones, as well as for granite pavers and slabs. King® MasonBond 400® is formulated with cementitious materials, polymer, masonry sand with controlled grain size, and other carefully selected additives.
- Factory calibrated mix
- High bond strength
- Superior workability
- High compressive strength and long-term durability
- Excellent resistance to de-icing salts
Usage
- Bonding brick and cultured stone to a variety of vertical surfaces
- Bedding granite paver and slabs on horizontal surfaces
- Installing steps in hardscaping work
- Can be used for interior and exterior applications
Advantages
- Factory calibrated mix
- High bond strength
- Superior workability
- High compressive strength and long-term durability
- Excellent resistance to de-icing salts
Packaging
30 kg (66 lb) triple-lined bags, polywrapped on wooden pallets
Colour
Powder / Grey
Product Details
Shelf Life
12 months in original, unopened bag
Storage Conditions
Always store in a dry area, protected from the weather. At the job site, an additional tarpaulin must be used to cover the product to prevent water infiltration.
Volatile organic compound (VOC) content
< 0.1 g/L (SCAQMD Rule #1168)
Compressive Strength
ASTM C109 - Minimum |
1 day | 7 days | 28 days |
8 MPa (1160 psi) | 15 MPa (2175 psi) | 20 MPa (2900 psi) |
Pull-Off Strength
CSA A23.2-6B / Bond Strength |
Support | Average Strength | |
MPa | psi | |
Concrete board | < 1.10 | < 159.54 |
Concrete board + metal lath | < 1.30 | < 188.55 |
Concrete block | < 1.26 | < 182.75 |
Porosity
EN-1015-7 Method / Air Content |
18 % Maximum |
Salt Resistance
ASTM C672 |
Number of Cycles | Mass Loss |
50 | < 50 g/m2 (1.5 oz/yd2) |
Application
Flowability
ASTM C1437
75 % +- 5% |
Product Temperature
Refer to the "Placement condition" section on the Specifications template document on Sika Canada Website.
Ambient Air Temperature
Refer to the "Placement condition" section on the Specifications template document on Sika Canada Website.
Substrate Temperature
Refer to the "Placement condition" section on the Specifications template document on Sika Canada Website.
Yield
Approx. 0.018 m3 (0.65 ft3) of fresh mortar per 30 kg (66 lb) bag
MIXING
Small quantity |
Important: In order to avoid segregation issues, always mix the total content of one bag. If less than a 30 kg of King® MasonBond 400® is required, dry mix - without water – the total content of the bag in a clean container, take the required amount, and then add water to the amount withdrawn from the mixture.
Large quantity
Always mix the entire content of the bag. Mix the King® MasonBond 400® with a maximum of 4.5 L (1.2 US gal) of water per 30 kg (66 lb) of mortar in a clean mortar mixer. Pour 4.0 L (1.0 US gal) of water into the mixer and add 30 kg (66 lb) of King® MasonBond 400®. Mix for three (3) to five (5) minutes. Allow the mortar to stand for a short period of time. Using the remaining water, adjust the mortar to obtain the desired consistency.
APPLICATION
The application of the mortar must comply with the requirements of Sections 6 and 7 of CSA-A371-14.
Refers to the King® MasonBond 400® Userguide available on Sika Canada Website
CLEAN UP
This product contains a polymer in powder form. Avoid contact with the surface of the elements to be installed.
In order to avoid the use of chemicals, it is always recommended to remove as much mortar splashes or stains as possible before the material hardens. Uses water, a piece of burlap or wood. If the use of cleaning products is necessary, be sure to contact the manufacturer of the product to validate the compatibility and the procedure to follow.
Regardless of the technique or product selected, it is essential to preserve the integrity of the mortar.
Be sure to clean a test area before proceeding with the work.
Clean all tools and equipment after use with water. Once hardened, the product can only be removed mechanically.